Ge power break ii manual

GE Industrial Solutions Power Break II Undervoltage Release User Manual

background image

Introduction

The Undervoltage Release (UVR) accessory, shown in Figure
1, can be installed in 800–4000 ampere frame Power Break®
II circuit breakers. This accessory trips the circuit breaker when
the input control voltage drops to 35–60% of its rated value
and prevents an open breaker from closing until the input
control voltage is greater than 80% of the rated value.
In addition to providing a trip signal to the breaker, the UVR
accessory can be set up to interact with other Power Break II
accessories, when used with a MicroVersaTrip Plus™ or
MicroVersaTrip PM™ Trip Unit. DIP switches on the rear of
the breaker Trip Unit can configure the UVR accessory to
activate a Bell Alarm–Alarm Only accessory or a Bell Alarm
with Lockout accessory when a UVR trip occurs. The Accessory
Configuration section below describes how this can be done. If
the breaker is equipped with a Power+™ Trip Unit, it is
configured so that only protection trips will activate a Bell
Alarm–Alarm Only or Bell Alarm with Lockout.
The catalog numbers for the UVR for various voltage
applications are listed in Table 1.

Figure 1. Undervoltage Release.

Operation

Apply control voltage to terminals 29 and 30 of the terminal
strip on the right side of the breaker. When the applied control
voltage is above 80% of the UVR’s rated value, the breaker can
be closed. When the voltage drops to 35–60% of the rated
value, the UVR will trip the breaker.

Catalog

Number

Voltage

Rating ❿

Peak Inrush

Current, A ❡

Nominal RMS

Current, mA

SPUV012DC

12 Vdc

19

300

SPUV024DC

24 Vdc

15

140

SPUV048DC

48 Vdc

7.5

70

SPUV125DC

125 Vdc

3

30

SPUV250DC

250 Vdc

1.5

15

SPUV024AC

24 Vac

15

370

SPUV048AC

48 Vac

7.5

210

SPUV120AC

120 Vac

3

80

SPUV208AC

208 Vac

1.9

60

SPUV240AC

240 Vac

1.5

45

24–240 Vac devices are rated for 50/60 Hz.

Peak inrush current is present for 2–6 ms after activation. This
number is provided so that fuses and supplies can be chosen
appropriately.

Table 1. Catalog numbers and voltages for the Undervoltage Release.

Installation

WARNING: Before installing any accessories, turn the breaker
OFF

, disconnect it from all voltage sources, and discharge the

charging springs.

AVERTISSEMENT: Avant d’installer toute accessoire, mettre
le disjoncteur en position OFF, le déconnecter de toute tension
d’alimentation, et décharger les ressorts d’armement.

The Undervoltage Release is installed in the accessory
compartment through the front of the circuit breaker in the
position shown in Figure 2.

Figure 2. Accessory compartment on front of circuit breaker, with

Undervoltage Release slot indicated.

g

Power Break

®

II Circuit Breaker

Accessories

Undervoltage Release

GEH–6285C

Sours: https://www.manualsdir.com/manuals/294777/ge-industrial-solutions-power-break-ii-undervoltage-release.html

GEH6271

WARNINGS, CAUTIONS, AND NOTES

AS USED IN THIS PUBLICATION

WARNINGS

Warning notices are used in this publication to emphasize that hazardous voltages, currents, or other conditions that could cause personal injury are present in this equipment or may be associated with its use.

Warning notices are also used for situations in which inattention or lack of equipment knowledge could cause either personal injury or damage to equipment.

CAUTIONS

Caution notices are used for situations in which equipment might be damaged if care is not taken.

NOTES

Notes call attention to information that is especially significant to understanding and operating the equipment.

This document is based on information available at the time of its publication. While efforts have been made to ensure accuracy, the information contained herein does not cover all details or variations in hardware and software, nor does it provide for every possible contingency in connection with installation, operation, and maintenance. Features may be described herein that are not present in all hardware and software systems. GE Industrial Systems assumes no obligation of notice to holders of this document with respect to changes subsequently made.

GE Industrial Systems makes no representation or warranty, expressed, implied, or statutory, with respect to, and assumes no responsibility for the accuracy, completeness, sufficiency, or usefulness of the information contained herein. No warrantees of merchantability or fitness for purpose shall apply.

The following are trademarks of GE Company:

Power Break®, MicroVersaTrip PM™, MicroVersaTrip Plus™, Power+™, POWER LEADER™

© 2001 GE Company

All Rights Reserved

Sours: https://manualmachine.com/geindustrialsolutions/powerbreakiidrawout8004000ampframes/1574380-user-manual/
  1. Gm suspension recall
  2. Silicone lighter mold
  3. Aaa travel jobs

SSF16B216 GE 1600 Amp 600V 3 Pole Power Break II Manually Operated Fixed Mount

$2,950.00Buy It Nowor Best Offer29d 2h, 30-Day Returns, eBay Money Back Guarantee

Seller:603-534-2392✉️(609)98.9%, Location:Barrington, New Hampshire, Ships to: US, Item:163911709051SSF16B216 GE 1600 Amp 600V 3 Pole Power Break II Manually Operated Fixed Mount. GE Power Break II SSF16B216 1600 Amp Frame600V 3 PoleManually Operated Fixed Mount Circuit Breaker Complete with:Trip Unit: B216LSI Rating Plug: TR16B1000 Clean Used - Excellent Condition All Items are Thoroughly Inspected and Cleaned Before Being Shipped Typically Ships Same Day or Next Business Day Many More Parts in Stock Call Cody for more Details!6035342392Condition:Used, Condition:Clean Used - Excellent Condition, Restocking Fee:No, All returns accepted:Returns Accepted, Item must be returned within:30 Days, Refund will be given as:Money Back, Return shipping will be paid by:Seller, Voltage Rating (AC):600 VAC, Current Rating:1600 Amp, Number of Poles:3, MPN:SSF16B216, Brand:GE

PicClick Insights - SSF16B216 GE 1600 Amp 600V 3 Pole Power Break II Manually Operated Fixed Mount PicClick Exclusive

  •  Popularity - 1,013 views, 1.4 views per day, 733 days on eBay. Super high amount of views. 1 sold, 1 available.
  • 1,013 views, 1.4 views per day, 733 days on eBay. Super high amount of views. 1 sold, 1 available.

  •  Price -
  •  Seller - 609+ items sold. 1.1% negative feedback. Top-Rated Seller! Ships on time with tracking, 0 problems with past sales.
  • 609+ items sold. 1.1% negative feedback. Top-Rated Seller! Ships on time with tracking, 0 problems with past sales.

    Recent Feedback

People Also Loved PicClick Exclusive

  • GE SSF16B216, W/ B216LSI Trip, 1200 Amp Plug- TEST REPORT + WARRANTY

    GE SSF16B216, W/ B216LSI Trip, 1200 Amp Plug- TEST REPORT + WARRANTY

    $2,400.00Buy It Now23d 0h

  • GE Power Break II SSF16B216 STD 1600A Circuit Breaker 1600 amp 600V 3 pole

    GE Power Break II SSF16B216 STD 1600A Circuit Breaker 1600 amp 600V 3 pole

    $3,000.00Buy It Now13d 22h

  • GE Power Break II SSD16B216 STD 1600A Circuit Breaker 1600 amp 600V 3 pole

    GE Power Break II SSD16B216 STD 1600A Circuit Breaker 1600 amp 600V 3 pole

    $1,750.00Buy It Now4d 1h

  • GE Power Break II Cat. SFF16B216 1600 Amp 3 Pole Circuit Breaker

    GE Power Break II Cat. SFF16B216 1600 Amp 3 Pole Circuit Breaker

    $1,600.00Buy It Now25d 2h

  • GE Power Break II Circuit Breaker CAT # SSF16B216, 1600 Amp, 3 Pole, Versa Trip 

    GE Power Break II Circuit Breaker CAT # SSF16B216, 1600 Amp, 3 Pole, Versa Trip 

    $2,190.00Buy It Now9d 1h

  • Ge Circuit Breaker Ssf16B216 1600A 600V 3Pole Type Tr16B 1Year Warranty

    Ge Circuit Breaker Ssf16B216 1600A 600V 3Pole Type Tr16B 1Year Warranty

    $6,999.99Buy It Now29d 23h

  • General Electric 1600 Amp 600V 3 Pole Insulated Case Circuit Breaker SSF16B216H

    General Electric 1600 Amp 600V 3 Pole Insulated Case Circuit Breaker SSF16B216H

    $1,800.00Buy It Now16d 3h

  • GE Breaker Cat # SSF16B216 1600 Amp 3 Pole w/1600 Amp Rating Plug MicroVersaTrip

    GE Breaker Cat # SSF16B216 1600 Amp 3 Pole w/1600 Amp Rating Plug MicroVersaTrip

    $2,180.00Buy It Now9d 1h

  • Ge Ssf16D216 Power Break Ii 1600 Amp 600 Vac Std Int Power +Front Fixed Icb

    Ge Ssf16D216 Power Break Ii 1600 Amp 600 Vac Std Int Power +Front Fixed Icb

    $3,000.00Buy It Now6d 5h

  • GE Circuit Breaker # SSF16B216 1600 Amp, 3 Pole, MicroVersaTrip w/1600 Amp Plug

    GE Circuit Breaker # SSF16B216 1600 Amp, 3 Pole, MicroVersaTrip w/1600 Amp Plug

    $2,185.00Buy It Now9d 1h

  • Ge Power Break Ii Ssf08B208 Circuit Breaker 800A/600V Xclnt Takeout! Make Offer!

    Ge Power Break Ii Ssf08B208 Circuit Breaker 800A/600V Xclnt Takeout! Make Offer!

    $1,799.99Buy It Now5d 4h

  • GE Power Break II SSF16B216 Circuit Breaker ~ 1600 Amp

    GE Power Break II SSF16B216 Circuit Breaker ~ 1600 Amp

    $5,000.00Buy It Now2h 49m

  • Ge Tps Tpss Tpss6620 3 Pole 2000 Amp 600V Circuit Breaker Power Breaker Manually

    Ge Tps Tpss Tpss6620 3 Pole 2000 Amp 600V Circuit Breaker Power Breaker Manually

    $2,999.99Buy It Now2d 0h

  • GE Circuit Breaker # SSF16B216 1600 Amp 3 Pole with TR16B 1600 Amp Rating Plug

    GE Circuit Breaker # SSF16B216 1600 Amp 3 Pole with TR16B 1600 Amp Rating Plug

    $2,175.00Buy It Now9d 1h

  • Ge Power Break Ii Ssf20G220 2000A 600V 3P Circuit Breaker

    Ge Power Break Ii Ssf20G220 2000A 600V 3P Circuit Breaker

    $4,800.95Buy It Now15d 1h

  • Ge Ssf08B204-B204Lsi 800Af/400As/400At M/O-Fixed Power Break Ii

    Ge Ssf08B204-B204Lsi 800Af/400As/400At M/O-Fixed Power Break Ii

    $2,955.24Buy It Now14d 5h

  • Ge Ssf16D216 1600 A Circuit Breaker  3 P 600 V Tr16C1600 Rating Plug Recon

    Ge Ssf16D216 1600 A Circuit Breaker 3 P 600 V Tr16C1600 Rating Plug Recon

    $4,500.00Buy It Now5d 2h

  • General Electric Ssf20B220 Circuit Breaker 2000A 600V 3Pole 1Year Warranty

    General Electric Ssf20B220 Circuit Breaker 2000A 600V 3Pole 1Year Warranty

    $7,999.99Buy It Now29d 23h

  • GE SSF16D216, 1600 Amp 3 Pole 600 Volt LI- W/ TEST REPORT

    GE SSF16D216, 1600 Amp 3 Pole 600 Volt LI- W/ TEST REPORT

    $5,000.00Buy It Now24d 0h

  • Ge Ssf16D216 1600Amp "No Gfi"

    Ge Ssf16D216 1600Amp "No Gfi"

    $1,500.00Buy It Now28d 4h

  • SSF16B216 GE 1600 Amp MO BI LSIG ships Same Day 1 Year Warranty

    SSF16B216 GE 1600 Amp MO BI LSIG ships Same Day 1 Year Warranty

    $5,500.00Buy It Now5d 6h

  • General Electric Power Break Manually Operated 2000A 3P 600V Cat. Tpss6620

    General Electric Power Break Manually Operated 2000A 3P 600V Cat. Tpss6620

    $3,495.00Buy It Now7d 4h

  • Ge Circuit Breaker Ssf16D216 1600Amp

    Ge Circuit Breaker Ssf16D216 1600Amp

    $2,025.00Buy It Now9d 1h

  • SSF20G220 SSF20B220 G.E POWERBREAK 2000A LSIG NEW ABB with switchboard

    SSF20G220 SSF20B220 G.E POWERBREAK 2000A LSIG NEW ABB with switchboard

    $11,800.00Buy It Now20d 6h

  • Ge Ssf20B220

    Ge Ssf20B220

    $3,500.00Buy It Now26d 1h

  • GE PowerBreak 11 #SSF16D216 1600A 3 pole with #TR16C1600,#D216LSI,with #TARGET00

    GE PowerBreak 11 #SSF16D216 1600A 3 pole with #TR16C1600,#D216LSI,with #TARGET00

    $2,500.00Buy It Now18d 18h

  • GE Power Break II Circuit Breaker, SSF16D216, 600VAC, 3 Pole, 3 PH, 1600A Frame

    GE Power Break II Circuit Breaker, SSF16D216, 600VAC, 3 Pole, 3 PH, 1600A Frame

    $5,250.00Buy It Now4d 22h

  • GE Power Break II 1600A 600V Circuit Breaker# SSF16G216 w/ Entelliguard Trip

    GE Power Break II 1600A 600V Circuit Breaker# SSF16G216 w/ Entelliguard Trip

    $5,000.00Buy It Now8d 1h

  • GE Power Break II SSF16D216 Break Circuit Breaker

    GE Power Break II SSF16D216 Break Circuit Breaker

    $4,500.00Buy It Now21d 4h

  • GE SSF08B208 Power Break II Insulated Case Circuit Breaker LSIG 3P 600V 800A MVT

    GE SSF08B208 Power Break II Insulated Case Circuit Breaker LSIG 3P 600V 800A MVT

    $5,000.00Buy It Now22d 8h

  • SSD16B216 GE 1600 Amp 600V 3 Pole Power Break II EO/DO Drawout Circuit Breaker

    SSD16B216 GE 1600 Amp 600V 3 Pole Power Break II EO/DO Drawout Circuit Breaker

    $7,500.00Buy It Nowor Best Offer

  • SSF16B216 GE STD Circuit Breaker 1600A 600V 3Pole

    SSF16B216 GE STD Circuit Breaker 1600A 600V 3Pole

    $3,800.00Buy It Nowor Best Offer

  • SSF16B216 GE 1600 Amp PBII MO BOLT IN

    SSF16B216 GE 1600 Amp PBII MO BOLT IN

    $7,200.00Buy It Nowor Best Offer

  • GE SSF16B216 Circuit Breaker 1600 Amp, w/ MicroVersaTrip Plus, 600V.AC

    GE SSF16B216 Circuit Breaker 1600 Amp, w/ MicroVersaTrip Plus, 600V.AC

    $5,999.00Buy It Nowor Best Offer

  • GE PowerBreak II SSF16B216  1600 Amp Breaker  with Microversatrip Lot AA129

    GE PowerBreak II SSF16B216 1600 Amp Breaker with Microversatrip Lot AA129

    $1,500.00Buy It Now

  • General Electric Power Break II 1200,1600 amp GE Breaker SSF16B216 w/test report

    General Electric Power Break II 1200,1600 amp GE Breaker SSF16B216 w/test report

    $6,800.00Buy It Nowor Best Offer

  • General Electric Power Break II 1600 amp GE Breaker SSF16B216 Ground Fault

    General Electric Power Break II 1600 amp GE Breaker SSF16B216 Ground Fault

    $6,800.00Buy It Nowor Best Offer

Sours: https://picclick.com/SSF16B216-GE-1600-Amp-600V-3-Pole-Power-163911709051.html

Power Break II GET 8052C 1000486169 Catalog

21

Metering

When the metering function is selected, a number of

standard metering parameters can be viewed on the LCD

display. All of these values are communicated to the POWER

LEADER™ Power Management System. The accuracy of the

metering functions is constrained by the physical size of the

current sensors. Consequently, all metering functions are

designed for load management decisions, and are not a

substitute for utility revenue metering equipment.

• Current: All trip units, including MicroVersaTrip Plus™, pro-

vide metering of individual phase currents. The user can

select phases 1, 2, or 3. Current displays automatically shift

from amps to kiloamps above 999 amps. The minimum

current display resolution is in tenths of an amp (e.g., 512

A).

• Voltage: The metering display of four wire systems can

read both line-to-neutral and line-to-line voltage display

for each phase. The smallest resolution of the voltage

display is one volt (e.g. 277V, or 276V).

• Energy: The energy display indicates the amount of real

power that has passed through the breaker. The display

has three-digit resolution, and automatically scales the

display from kWh to MWh to GWh. Normal power flow can

be selected as either load-line or line-load in the setup

mode. Once normal flow is configures, energy values will

accumulate in the positive direction. For certain applica-

tions where power may flow in either direction, such as tie

breakers, energy may display a negative value.

• Real power: Real power in units of kW or MW can be

shown on command on the LCD display.

• Volt-amperes (or total power): “Total power” or volt-am-

peres in units of kVA or MVA can be viewed on command

on the LCD display.

MicroVersaTrip Plus™ and PM™ Trip Units

• Demand: Demand in units of kW or MW can be displayed.

The monitoring time period can be varied from 5 to 60

minutes, in increments of 5 minutes. The display provides a

rolling average of power over the scheduled time interval.

• Peak demand: Peak demands in units of kW or MW can be

displayed. This value indicates the highest power demand

reached since the start of demand measurements, or since

reset. The peak demand value can be reset to the present

demand via the keypad.

Protective Relaying

When protective relaying functions are selected, any combi-

nation of the following protective relays can be enabled. All

relay functions combine both an adjustable setpoint and an

adjustable discrete (not inverse) time delay. All time delays

are adjustable from 1 to 15 seconds in increments of 1 sec-

ond. All tripping is performed through the trip unit. The user

can configure the trip unit to activate the bell alarm only, the

bell alarm with lockout, or neither, in response to a protective

relay (or overcurrent/ground-fault) trip.

• Undervoltage: Undervoltage protection may be set from

50% to 90% of the true rms nominal voltage in increments

of 1%.

• Overvoltage: Overvoltage protection may be set from

110% to 150% of the true rms nominal voltage in incre-

ments of 1%.

• Voltage unbalance: Voltage-unbalance protection com-

pares the lowest or highest phase voltage with the other

two, and initiates a trip if the difference exceeds the

setpoint. True rms voltages are computed for each phase.

The range of trip settings varies from 10% to 50% in incre-

ments of 1%.

• Current unbalance: Current-unbalance protection com-

pares the true rms current in either the highest or lowest

phase with the true rms current in the other two phases. A

trip is initiated if the difference exceeds the setpoint. The

range of trip settings varies from 10% to 50% in incre-

ments of 1%.

• Power reversal: The Power Break® II breaker may be set

so that “positive” power flow can be in either direction (i.e.,

from line to load, or vice versa). Reverse power protection

is set in units of kW. Reverse power setpoints vary from

10kW to 990kW in increments of 10kW.

• Enable/disable relays: To disable any of the protective

relay functions, set the time delay for that function to OFF.

Setting the time delay to any discrete value enables the

relay.

Table 21.1 Trip Unit Metering Display Accuracy

ValueBreaker Full Scale

Accuracy

System Full Scale

Accuracy

Current, rms –A, kA±2.5%±2.5%

Voltage, rms –V

Phase-Phase, Phase-Neutral

N/A± 1.5%

Energy –kWh, MWh, GWhN/A±4.0%

Demand – kW, MWN/A±4.0%

Peak Demand- kW, MWN/A±4.0%

Real Power – kW, MWN/A±4.0%

Total Power – kVA, MVAN/A±4.0%

FrequencyN/A±1 Hz

Time DelayN/A±1 sec

Includes trip unit, breaker, current sensors and rating plug. Accuracy is based on

loading range of 20% to 100% of breaker current sensor rating.

Includes trip unit, breaker, current sensors, rating plug, plus Voltage Module (poten-

tial transformers, control power voltage conditioner). Accuracy is based on loading

range of 20 % to 100 % of breaker current sensor rating.

Sours: https://usermanual.wiki/Pdf/1000486169Catalog.2088317830/html

Power ii ge manual break

.

.

You will also be interested:

.



2390 2391 2392 2393 2394